Spindles and ATCs

PwnCNC ATC System This is where you can discuss anything and everything having to do with the ATC System. PwnCNC Spindle System Maintenance This category is set aside for learning about various techniques to maintain your spindle and ATC motors. This is an important topic.

Topic	Replies	Views	Activity
About the Spindles and ATCs category Spindles and ATCs	0	100	December 11, 2023
Broken wire on top of ATC spindle PwnCNC ATC System	1	23	November 5, 2025
Err31 code - any ideas? Spindles and ATCs	2	54	October 14, 2025
Motor Break-in and Warm-up Procedures Maintenance	17	640	September 25, 2025
ATC Pneumatics Enclosure Spindles and ATCs	6	101	September 14, 2025
ATC is not allowing change of tools PwnCNC ATC System	11	94	September 13, 2025
Onefinity Redline Controller Spindles and ATCs	5	188	August 17, 2025
How many cutters are used in any one Item made Spindles and ATCs	5	68	August 16, 2025
2.2kw 220v ER20 80mm 2-pole 400Hz Water-Cooled Power requirements Spindles and ATCs	3	51	August 15, 2025
Bullet Type Spindles Spindles and ATCs	4	75	June 18, 2025
"Tool Error" with New ATC Setup Spindles and ATCs	3	58	June 14, 2025
MTC handle File for 3d print Spindles and ATCs	3	38	June 4, 2025
Masso 5.09 and ATC. Use at own risk PwnCNC ATC System	12	255	May 27, 2025
ATC Dropping tool early PwnCNC ATC System	7	80	May 27, 2025
Recommended dust boot for your ATC on a OF Z20 PwnCNC ATC System	30	290	May 14, 2025
Soft limit options Spindles and ATCs	21	107	May 3, 2025
Z Axis Cable Management Spindles and ATCs	2	72	April 29, 2025
Soft Limits for tool rack Spindles and ATCs	7	63	April 19, 2025
VFD Extension Cables w/ATC Spindles and ATCs	5	86	April 17, 2025
Carbide3d VFD conversion to Masso controller Spindles and ATCs	4	63	April 14, 2025
Tool Changer Help! PwnCNC ATC System troubleshooting	1	74	April 10, 2025
Spindle Dead After 1F Upgrade Spindles and ATCs	9	171	March 24, 2025
ATC on shapeoko 5 Pro PwnCNC ATC System conversion-kit	17	160	March 20, 2025
ATC not releaseing tool properly or clamping tool properly Spindles and ATCs	1	49	March 10, 2025
HuanYang VFD/ Zhong Hua Spindle vs PWNCNC VFD/Spindle speed tracking Spindles and ATCs	6	79	February 26, 2025
VFD display continues to blink after VFD power switched off Spindles and ATCs	3	63	February 11, 2025
Movd my CNC and now the spindle won't start automatically Spindles and ATCs	6	110	February 7, 2025
PSA: Low Cost / No Cost Buckets Spindles and ATCs	2	44	January 29, 2025
gSender 1.4.11 spindle will not turn PwnCNC Spindle System	2	81	January 29, 2025
2.2 water cooled spindle Spindles and ATCs	1	75	January 21, 2025