# VFD Keypad mount hardware

**URL:** <https://forum.pwncnc.com/t/vfd-keypad-mount-hardware/460>\
**Category:** Onefinity\
**Created:** [January 26, 2024, 1:55am UTC](https://forum.pwncnc.com/t/vfd-keypad-mount-hardware/460 "2024-01-26T01:55:42Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Rizzo](https://yyz1.discourse-cdn.com/flex011/user_avatar/forum.pwncnc.com/rizzo/32/660_2.png) [@Rizzo](https://forum.pwncnc.com/u/Rizzo)\
**Post date:** [January 26, 2024, 1:55am UTC](https://forum.pwncnc.com/t/vfd-keypad-mount-hardware/460/1 "2024-01-26T01:55:42Z")

</div>

I purchased the 3d file for the VFD Keypad Mount and I was wondering what size/thread/length screws are needed to mount to the back of the masso display on the 1finity elites? I haven’t received my cnc yet, but was going to make sure I had the right hardware on hand for when it came. Thank you in advance.

---

<div class="post-metadata">

**Author:** ![Chris](https://yyz1.discourse-cdn.com/flex011/user_avatar/forum.pwncnc.com/chris/32/54_2.png) [@Chris](https://forum.pwncnc.com/u/Chris)\
**Post date:** [January 26, 2024, 2:28am UTC](https://forum.pwncnc.com/t/vfd-keypad-mount-hardware/460/2 "2024-01-26T02:28:43Z")

</div>

Masso takes an m3 in those holes. On the inside its where the relays go. 10mm or 12mm should be enough, but i don’t have the masso mount given it doesn’t fit my workflow.

---

<div class="post-metadata">

**Author:** ![Rizzo](https://yyz1.discourse-cdn.com/flex011/user_avatar/forum.pwncnc.com/rizzo/32/660_2.png) [@Rizzo](https://forum.pwncnc.com/u/Rizzo)\
**Post date:** [January 26, 2024, 2:30am UTC](https://forum.pwncnc.com/t/vfd-keypad-mount-hardware/460/3 "2024-01-26T02:30:32Z")

</div>

Thank you so much Chris, you are amazing!

---

<div class="post-metadata">

**Author:** ![Chris](https://yyz1.discourse-cdn.com/flex011/user_avatar/forum.pwncnc.com/chris/32/54_2.png) [@Chris](https://forum.pwncnc.com/u/Chris)\
**Post date:** [January 26, 2024, 2:36am UTC](https://forum.pwncnc.com/t/vfd-keypad-mount-hardware/460/4 "2024-01-26T02:36:11Z")

</div>

Thank you, I do try.

---

<div class="post-metadata">

**Author:** ![Oseanmc](https://yyz1.discourse-cdn.com/flex011/user_avatar/forum.pwncnc.com/oseanmc/32/661_2.png) [@Oseanmc](https://forum.pwncnc.com/u/Oseanmc)\
**Post date:** [January 26, 2024, 6:43am UTC](https://forum.pwncnc.com/t/vfd-keypad-mount-hardware/460/5 "2024-01-26T06:43:52Z")

</div>

Rizzo, I went with the same VFD remote mount. Just be aware that once mounted there you have to remove it to open the Masso controller screen/door. I ended up using CA glue to attach it to the same spot without impeding the door/screen.  
FYI